Fitting a Evo2 or Cecotto front spoiler

Fitting a Evo2 or Cecotto front spoilerThis article is just to give a hand to fit a aftermarket evo2 spoiler to you're M3 bumper.
Most of the aftermarket stuff are copies from originals, some of them even have the oem BMW numbers in them.
Mostly they are made from polyester.
Polyester has a benefit of being light weight and it can bend.
But between ABS and polyester, polyester will brake, where ABS will be dented.
Polyester when molded also has another drawback, it can shrink, this depends on the temperature, quality of the resin and so on.
It can shrink as much as 1cm per meter.
Now that we know a little about the materials that we are working with, we can go on talking about fitting the evo2 spoiler.

Fitment is quite easy
Before painting the spoiler, always check you're fitment.
Use some paper tape for you're bumper, so you won't scratch of any paint
Press it on, and yes, you have to press well, the lips behind the bumper have to lock it in place.
Look around the upper edges if you have to sand off some material.
When you're happy with the result, we can start drilling holes.
It's best to have a mate help you so that the spoiler doesn't shift while drilling.
Later on I will talk about some troubleshooting, but for now we will go on with fitting the spoiler.
Fitting a Evo2 or Cecotto front spoilerIn the 2 corners of the spoiler and bumper, you can drill a bigger hole for a screw, I used a clamp with thread in it with a screw.
Those you can get by any local moped/motor dealer, all the covers are fitted like this.
For the bottom I used plastic press buttons or expanding rivets, those you can order at you're local BMW dealer.
order number ETK 51 16 2 121 287
In the next picture you can see how the result looks with the rivets.
A few holes are enough, you don't want to make Swiss cheese from it
On the bottom here you can see the screws where to place them.
The Evo2 spoiler is already in a proper form to keep itself into place

After all this, you can de-mount the spoiler and getting to paint it.
Now, the trouble shooting.
Some things you'd should know.
We talked before about some of the properties of polyester.
Another one is that it will miss form when it sees to much heat.
A sunny day won't be a problem, but the paint booth would.
It would be a downside if you would do all this trouble and get back you're spoiler and it won't fit.So tell you're painter to let the paint cure without heat treating it.
Most of us will order a spoiler overseas and not from the corner store.
The seller's don't want the postman to mess up the spoiler so they normally pack it in really well.
But in time with transfer, there always can get some miss forming.
So when you first try to fit it, and it won't fit at once like a condom, don't directly blame the maker of the product.
Fitting a Evo2 or Cecotto front spoiler Remember what I said in the beginning, most of the spoilers are copies of a original.
If this is the case, you're spoiler wont fit properly, we can use some of the benefits of polyester again.
Most of the time, due to packaging, the middle part wont line up properly and will look to low.
You can measure the gap that you miss, and put anything between it so that it will widen and the gap gets bigger.
I used a little block of wood.
But then again, you can use anything.
You can let it set overnight in a nice warm environment, and the polyester will automatically take a bigger shape the next day.The alignment on the outsides sometimes require some force.
You can damage, or scrape you're original bumper.
So the best thing you can do is tape up the corners, use the paper tape and not the thick McGuiver tape.
So don't be afraid to use some force.
For example, my car was freshly painted, first day/evening I went out for a spin, I hit a rabbit with over 100Km/h
The spoiler didn't break or let loose,  it shifted a little downwards, but no significant damage.
The bumper itself on the other hand had a crack in it because of the rabbit.
So you see how strong it is, but I can't recommend it for hunting purposes.

 


Parts 4 sale

Fitting a Evo2 or Cecotto ...

Fitting a Evo2 or Cecotto front spoiler

...

Lees meer..

E30 M3 CECOTTO AC Schnitzer ...

E30 M3 CECOTTO AC Schnitzer Project
In ...

Lees meer..

E30 M3 Evolution III 2.5 ...

This picture story is about an ...

Lees meer..

E30 M3 Cecoto Evo2 ...

BMW E30 M3 front spoiler Evo en ...

Lees meer..

E36 M3 3,2 fuelpomp

E36 M3 3,2 fuelpomp
75 euro

Lees meer..

E30 M3 Evo 3 rear spoiler

BMW E30 M3 evo3 ...

Lees meer..

E30 M3 DTM finned ...

E30 M3 DTM finned differential cover
...

Lees meer..

home


Danny Special Parts is a company based ...

Lees meer..

Contact Menu

Ebay seller

Here are our Ebay items: